They are making a few good pointers related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in the article which follows.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Setting up a bathtub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a new one is additionally a moderately difficult task. If the old tub is readily obtainable, the job can move easily; if you have to open a wall surface to remove the old bathtub as well as position the brand-new bathtub, the job is much harder. In either case, the task is within a home handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the new one. See to it you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is far better to consider utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This short article will certainly help you mount a new bath tub in your bathroom if you have currently purchased a brand-new tub as well as do not need to transform the arrangement of your previous water system pipes.
Your tools and also material list should make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will come from the pipes. When the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washers are in location between the tap and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type should be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the level checks out level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and also the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the tub needs to wait until the bath tub has actually been used at the very least once as this will certainly settle it right into its final placement.
Getting ready for the Installment
First of all, the sustaining framework provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about complications with dampness and possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components as well as installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to sealing, to enable the motion experienced when the tub is in use. The sealant can crack fairly very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the market. It is suggested to fit the floor tiles using water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our section about Installing A Bathtub. Thanks a ton for finding the time to browse our piece. Enjoyed our entry? Please share it. Let somebody else check it out. Thank-you for your time spent reading it.
Go Deal